|
2002 Audi A6 3.0L shifting? Hi everyone. Thanks in advance for your help.
We have a strange problem on this Audi. Under light to
moderate acceleration, it has a slight slip (for lack of a
better description, I'll call it a slip) at faily regular
intervals. It feels like the engine has a... |
View |
|
2003 Audi A4 3.0L Unknown i need a spec on the parristic draw on this ayatem i cant
seem to find the spec any where thanks in advance |
View |
|
2000 BMW 740iL 4.4L Electronic Help all BMW techs! We just replaced abs conrol unit for
this car. Customer called afew days later saying a/c was
inop. We scanned for faults with gt1- none. a/c charge is
correct.Compressor clutch not energized. we found no signal
was being recieved from high... |
View |
|
2001 Land Rover Discovery 4.0L Regulator Good Morning Land Rover Tech's!
I have this Discovery in here and after replacing the
original drivers side window and regulator with a new part
from World-Pac, I am having cronic regulator failures.
The reason for the original glass and regulator replaceme... |
View |
|
1991 Mercedes-Benz 300SEL 3.0L Temp Gauge I have this mercedes with an intermittently fluctuating
temp gauge. I've narrowed it down to connector on back of
cluster or cluster. What I need is a schematic for the the
cluster specifically, which pin does what and what color
wires connect to it. My fax # ... |
View |
|
2001 Mercedes-Benz E320 3.2L No Start, Cuts out the car will stall on decel under 10 mph.and it will not
start for at least 5 mins.(cranks ok), but it also
sometimes will not start when is being parked for a while.
but it will only do it sometimes, customer states it has
done it 5 to 6 times each time it ha... Trouble codes: p2034 (undocumended code). |
View |
|
2005 Mercedes-Benz C230 1.8L belt tensioner This vehicle came to us after customer was told by another
shop they "could do no more" to repair it. The symptom is
at idle in gear, a/c on or off at just the right rpm the
belt tensioner starts slapping back and forth about 3/4 of
an inch and making a knocki... |
View |
|
1972 Porsche 914 1.7L Poor Idle Quality hey guys a buddy of mine bought the heap.it has mecanical
injectors and pionts.the issue is that I can not find and
info on this vehicle also when coming to a stop after awarm
it will idle at 1500 and if you give it a shot of gas it
will come down and almost s... |
View |
|
2000 Volkswagen Jetta 2.8L Communication Came in with Traction control, ABS & SRS lights on.
When Ross-Tech Vag-Com hooked up I can't get the unit to
communicate to any modules. (works fine on other cars)
Looked at the aftermarket radio scenario, DLC pin #7 is NOT
geting Battery voltage from afterm... |
View |
|
2001 Volkswagen Jetta 2.8L No Start A customer bought this car on E-Bay as is and had it towed
here because it would crank but wouldn’t start. First off,
we were unable to communicate with any modules and there’s
no damage to the DLC or any of the wiring. Because it
wouldn’t even fire, I tried a... |
View |
|
2002 Volkswagen Passat 2.8L Poor Idle Quality This vehicle has a mild shake at idle but no other
driveabilty issues. We've changed the plugs, wires and
valve cover gaskets (leaking oil onto spark plug boots).
Everything scans well, but we noticed on a compression test
that the left bank took 7 turn overs ... Trouble codes: P0300 (RANDOM MISFIRE - intermittently and CEL has never come on). |
View |
|
2003 Volkswagen New Beetle 1.8L Poor Idle Quality, Misfire, MIL Lamp on well this is what happening with this bug had codes listed
on cold start this unit fires up missing on 1 and 2 in
about 60 seconds it runns fair quits missing any how i
swaped coils 1234 to 4321 and no change fine no coil
problem so did same with injectors and... Trouble codes: 16716 (knock b 2), 17519 (o2 bank1 lean), 17560 (o2 bank lean), po300 (random), po301 (1 missfire), po302 (2 missfire). |
View |
|
2000 Volvo C70 2.3L closing Hi Volvo tech's,. we have this top that retracts OK but on
closing it stops about 3 inches from closing. The codes are
CCU-311 C/Top closing circuit to high and CCU-312 C/Top
opening circuit too high. Was wondering if anyone has seen
this problem before? Thank... |
View |