|
|
1997 Chrysler LHS 3.5L pw, a/c,air bag This is a strange one to me. this car has been fairly
trouble free for the owner but every once in a while and
more often lately the air bag and abs lamp will lite and
when they do the A/C and Power Windows are inoperative. We
put the modis on the car and on t... |
View |
|
1999 Dodge Ram Van 5.9L Cuts out, Stall, Misfire, MIL Lamp on This is a fleet vehicle. This van will occasionally
hydrolock with fuel. What happens is the #6 & #8 fuel
injector will pulse non stop and flood both cylinders. At
the same time the ASD relay, fuel system relay, trans relay
and the evap purge solenoid will pul... |
View |
|
1999 Dodge Pickup 5.2L fog lamps Hey again fellow techs and god bless all at IATN!!! I first
ask you to ignore the vin. I need to ask a general question
of you all. In the state of virginia, with all fog lamps,
the fog lamps must cancel via the bright switch. When the
brights are clicked on t... |
View |
|
2000 Dodge Grand Caravan 3.8L No Start, No Crank First i want to thank everyone who takes the time to read
this long post and any help would be greatly
appreciated!This van 1st came in with a No Crank issue, the
costumer installed a New Battery and replaced Starter
Relay. First thing I did was get in vehicle... Trouble codes: 36 (ABS Module BUS Communication Error), 33 (ABS Module ABS Warning Lamp Circuit), 04 (Instrument Cluster No Engine Controller Messages), BCM (BCM No Codes but read SBEC Distance Pulse message not received). |
View |
|
2003 Dodge Caravan 3.3L gages, warning lights customer came in complaining the abs light , brake light,
oil light and ses light were comming on while she was
driving. also at the same time the tach and speedo stop
working also the prndl indicator stop working. we also
discovered that the a/c control power... |
View |
|
2005 Dodge Sprinter 2.7L srs light Vehicle came in with off center steering wheel. were
informed that the steering column had been worked on before
so thought the steering wheel was installed incorrectly.
After removal we found little latitude for being off
because of wiring indexing. after rei... |
View |
|
1986 Jeep Cherokee 2.8L Stall, hard start Hello to all,
I have a problem child. The Jeep came in after sitting for
several years. Running very poorly and with blown exhaust
manifold gaskets. The new owner told me to keep it until it
is fixed...I put new manifold gaskets on and performed a
complete tu... |
View |
|
1995 Chrysler Cirrus 2.5L key fob The reason for attempting to program the fob was that the security was set. As it turned out I had to disarm the security system first. Supplying power to pin 20 of the bcm accomplished this. Once this was done I was able to program the new fob. Thanks for the... |
2 |
|
1995 Dodge Pickup 5.9L no 3-4 shift or convertor lock-up Thanks to the members that sent in fix ideas, Jim, James, Bradley, Joe and Brad. The problem ended up being a bad ground at the tps connector . The ground connection was bad, the ground tested good when back-probed and at the ecm . The thing that threw me was ... |
5 |
|
1996 Dodge Neon 2.0L MIL Lamp on Thanks to those whom took the time to reply to my help request. After rechecking grounds and wiring it was determined that the PCM was bad. I replaced the PCM and test drove vehicle all is well and vehicle is repaired. Thanks once again for your replies and be... Trouble codes: P0132 (O2 sensor circuit high voltage B1S1). |
4 |
|
2000 Dodge Durango 4.7L Poor Idle Quality, Hesitation, Surge, Stall, Misfire, Poor Fuel Economy, MIL Lamp on not the fix i wanted but i guess. The coustomer had us jumper both relays to ground so when the key is on the relays are on and im sure this caused several codes but the coustomer is right and also dont care. Im sure it needs a computer and its depressing not... Trouble codes: P1282 (fuel pump relay circuit), P1495 (ldp sol circuit), P1388 (asd relay circuit), P1491 (fan relay circuit), P1389 (no asd relay boptput at pcm), P0622 (generator field not switching). |
6 |
|
2006 Dodge Charger 5.7L temp I had tracted the problem to the front control module not supplying a ground to the high fan relay with my wiring digrams but I was hesitant to make the call so I sent it to the dealer and was told the fan was the problem. so they installed a new fan motor--di... |
3 |
|