Prev iATN Members TechHelp for May 21, 2008
Automotive Technical Exchange for the Automotive Repair Professional		 Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
1996 Chrysler LHS 3.5L Poor Idle Quality, Cuts out
This car has a rough idle, worse when cold. Sometimes it will cut off without warning (cold or hot), when it does I cannot just crank it back up, I have to hold the throttle down a little, start it and hold it at over 1k rpm for a few seconds and then slowly l...		 View
2000 Dodge Intrepid 2.7L water pump
I am replacing the water pump on this vehicle, when I reinstall the timing cover it will not go flat against the engine, it seems to be held out in the center by the water pump. I have measured the bosses on the water pump that the timing cover bolts to and se...		 View
2000 Dodge Intrepid 2.7L Surge, Cuts out, Misfire, MIL Lamp on
I'm posting this for my boss, but I've been involved extensively. Car came in for MIL on and power loss at and above 3000 rpm, feels like it hits a rev limiter. Scoped CMP and CKP and had no CMP signal. When car came in, it had major extended crank before it w... Trouble codes: P0340 (Cam Signal Lost), P1391 (CkpCmp Correlation Problem).		 View
1987 Jeep Wrangler 4.2L 5th gear
My question is will the clearence in the other gear efect 5th gear? the tranny is Peugeot type.I must be missing something.I have replaced 5th gear once after rebuild. thanks in advance		 View
1994 Jeep Grand Cherokee 4.0L transfer case
This Jeep will creep forwards or backwards when in park. It has a full-time 4wd system (4 high and 4 low only). The transmission has been recently replaced and the parking pawl in fully engaging. The truck came to us missing the front driveshaft (from transfer...		 View
2003 Jeep Liberty 3.7L No Start
HELP this 03 jeep liberty 3.7 is killing me, i am almost certain the timing chain on the right cylinder head jumped a tooth, the 3 cylinders on that bank are fuel soaked, but not on the other, spark is good on all cylinders, injectors ramped out good and flow ...		 View
1995 Plymouth Grand Voyager 3.3L Drive-axles
this van came in for checking the pulling and vibrate or wobble /shaking under initial load. we found the motor mounts are broken and axles boots torn. we replaced all mounts inserts and rem cv axles and do the alignment. now the van is still slight wobble whe...		 View

Fixes & Summaries for Chrysler
Fix/Summary Answers
2004 Chrysler Concorde 3.5L Cooling Systems
first of all i'd like to thank all who replied. the customer wanted second opinion on pulling cylinder heads. sent vehicle out to local chrysler dealer who had car for a week, they pulled heads and discovered several coolant passages that were sverely plugged....		 8
2001 Dodge Grand Caravan 3.3L Unknown
Thanks to everyone that replied. We found that the left inner 'cv' axle had some play in it. We replaced the drive axle which in turn did take care of the shimmy. Thanks again!		 16
1981 Jeep CJ7 4.2L temp gauge
I want to thank everyone for their input on this one. I have to admit it was a lot harder than it should have been. I learned a few things one this one. 1) Make sure the engine is a operating temperature. I found that there was no thermostat in the engine, ...		 5
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next