|
1994 Audi 100 2.8L air bag HELP!! I HAD A OLD 94 AUDI 100CS COME IN FOR A STATE INSP.
WITH A AIR BAG LAMP ON. I DON'T HAVE ANY INFO ON DIAG. THIS
SYSTEM. I'M USING A SNAP ON BRICK TO PULL CODE 00588, HIGH
RESISTANCE-DRIVER SIDE IGNITOR. I ASSUMED (YOU KNOW WHAT
THAT MEANS) THAT IT WAS A... |
View |
|
1999 Audi A6 2.8L coolant Vehicle came in overheating. Overflow was cracked. Replaced
overflow. Vehicle got hot very quickly and started to boil
over like there was a flow issue. Replaced t-stat and
gasket. vehicle ran for approx. 2 hours in the bay. figured
it was ok. put cap on overf... |
View |
|
2000 Audi A6 2.8L solenoid 6-N93 This A6 will go into limp mode a couple times a week, when
the car acts up we get a transmission code of "00268
solenoid valve 6-N93 short with power intermittent" we
dropped the pan and inspected the wiring to the solenoids
and replaced the solenoid also, rea... |
View |
|
2006 Audi A3 2.0L ac compressor Hi all techs! a3 presented w/ ses lite [po301]and complaint
of intermittent cooling. hooked gauges and had 100 lbs on
both sides w/ system set on max cool [lo].found good info
from mitchell on square wave and amperage. my control and
ground appear to be perfec... |
View |
|
1991 BMW 325i 2.5L ABS dash light Hello Men, this car was brought into our shop with ABS
light on. It will not pass safety inspection with ABS light
on. The sensors are expensive, so no room for mistakes. Has
anyone pinned out the sensors for a positive ID on sensor
failure or know the steps o... |
View |
|
1998 BMW M Roadster 3.2L airbag Good morning BMW techs I have this Z3 M roadster with mouse
damage.Customer has just pulled out car after winter
storage to find that the power windows no longer work and
the airbag light is on.I found all the wires under the
shifter were chewed off.repaired t... |
View |
|
2002 BMW 330Ci 3.0L a/c blower, instrument cluster customer came in with complaint of a/c blower malfunction
(surging/ cutting out). charging and oil lights were on on
instrument cluster. we have replaced the final stage blower
and conditions stay the same. did sweep on gauges
(instrument cluster): fuel gauge ... |
View |
|
1984 Mercedes-Benz 380SL 3.8L Hesitation, Cuts out Having problems with this Mercedes. Very slow to respond to
accl. petal. Cuts out, and falls on its face on any demand
for fuel. If you apply slowly it isn't too bad. We replaced
fuel pump and filter at the request of the customer as we
did not know his compla... |
View |
|
1990 Mercedes-Benz 300SEL 3.0L compressor I cannot get the A/C compressor to switch on. There is
freon in the system, pressure switch is closed. I get no
output from the MAS unit to the clutch. The clutch speed
sensor puts out a signal, there is an ignition signal to
the MAS. I don't seem to be gettin... |
View |
|
1994 Mercedes-Benz S500 5.0L asr car came in w/asr light on and in limp in mode. wiring from
ea,cc,isc fried. replace unit with rebuilt. did not help,
sent unit back to rebuilder who insisted that unit is
working. replaced asr module w/known good module. same
problem. dtc readout is 120, miss... |
View |
|
2002 Mercedes-Benz C230 2.3L compressor Hello Friends: I need some advice with this vehicle,
because it is my first time working with this kind of
compressor. The compressor doesn't have magnetic clutch, it
is extarnally control by a selenoid valve. The compressor
is broke in its body so I have to r... |
View |
|
2000 Saab 9-5 3.0L Starting Car came in with no start, He had been in the flooded area
of the North coast Dom Rep carpet was soaking wet, After
flood he noticed that the alarm siren did no work two weeks
later No Start condition, Had car towed in no theft light
with ignition on , removed... |
View |
|
2001 Saab 9-5 2.3L starter wont crank pull out hairs here, replaced starter with good bosch,
replaced relay car never acter up while at the shop,
customer says: "when hot will not crank" any help
appreciated |
View |
|
2004 Volkswagen Jetta 1.9L No Start, Poor Idle Quality, Stall This car was brought to me to replace the timing belt and
waterpump. Customer furnished all parts and everything was
supplied. We have done these before and have never had any
problems. I do not do any work to the injection system on
these cars because I do no... Trouble codes: p0401. |
View |