|
1992 BMW 850i 5.0L uncknown This 8501 will not charge battery at idle after turning
engine on. After accelerating car up to about 3000 -
4000rpm it will start charging. After that even at idle
charging is normal.
Tachometer is not working at instrument panel. There is
some other instrum... |
View |
|
2001 BMW 325Ci 2.5L No Start I need some help from you BMW guys. I have this 325 that
has a very intermittant no start. I cant get it to happen
here. I did add a LED to the power and grond turn on wires
for the DME relay. The customer stated it did not light up
while trying to start. Powe... |
View |
|
2003 BMW X5 4.4L battery SUV came from another shop with a battery death after 2
hours car locked or unlocked. They've replaced battery but
still. I found here that the radio is on all times even
with key out of the ignition, also we got data from ZKE
module telling me that driver's a... |
View |
|
2004 Buick Rendezvous 3.4L All Windows Customer brought vehicle in with the complaint of
intermittent window operation, we were able to get windows
to fail all the time, pulled codes and found B1477 RAP
relay control circuit low and B1507 Low voltage on control
circuit, we performed test and pinpoi... |
View |
|
1995 Cadillac Eldorado 4.6L Poor Idle Quality, High Idle We replaced the IAC motor, no change. Start car, goes to
3500RPM, will go to 1000, but no lower. We took IAC off,
can lower idle by hand. We also did an idle re-learn, no
change!! HELP!! Trouble codes: 27 (Throttle Switch or Circuit Openhistory code), 52 (Defective ECMECU RAM Chip error history codde), 109 (Internal ECM Problem KAM Checksum history code). |
View |
|
1996 Cadillac DeVille 4.6L MIL Lamp on vehicle came in to shop running poor and ses light on,
originally. 6 codes stored po171, po174, po131, po138,
po151,p1139. fixed poor run with plugs, wires, and fuel
filter and cleared codes. (hoped repair would eliminate
some codes) vehicle returned with same... Trouble codes: PO131 (sig. low b1-s1), PO138 (sig. hi b1-s1), PO151 (sig low b2-s1), PO171 (sys. lean b1), PO174 (sys. lean b-2), P1139 (ho2s b-1 s-2 insufficient switching). |
View |
|
1988 Chevrolet Corvette 5.7L No Start We have this corvette here that intermittently has no
injector pulse. We have it narrowed down to a bad vats
module. When it wont start we have no signal on the vats
wire at the ecm. When it will start we have a perfect
signal. My question is, how do you get t... |
View |
|
1991 Chevrolet Pickup 5.7L charging gauge with the original alternator truck charges good 13.8 to
14.0 volts.only when u turn on blinkers or hazerd the
charging needle in the cluster starts fluctuating and
moving down at the speed of the turn flashes till it
reaches 12 volts and stops charging. after ... |
View |
|
1995 Chevrolet Camaro 3.4L Misfire GM Techs, Here is this camaro yet. Come in for misfire. Ran
tests and found #1 Injector not flowing any fuel. Spark
plug was fouled(black). Sandblasted spark plug to clean,
had good compression(not running), has good spark. Replaced
the fuel injector on #1 wit... |
View |
|
1999 Chevrolet Pickup 7.4L Poor Idle Quality, Misfire Hi Everyone and thanks in advance for the help. This truck
came to us after the customer replaced the plugs and wires
Due to a misfire.( He installed Bosch +4 plugs, I would
have used Delco's) That did not fix the problem so now it's
my problem. With 87k on th... |
View |
|
1999 Chevrolet Venture 3.4L door locks The customer came in with this van and the the doors keep
tring to unlock. I went out and the locks keep activating
in the unlock mode about 4-5 times a minute and then they
stopped, it sat here and about a half hour later it started
doing it again. I did noti... |
View |
|
2000 Chevrolet Suburban 5.3L Mechanical NO COLD AIR IN FRONT!!COLD IN REAR. THIS VEHICLE WILL NOT
BLOW COLD AIR IN THE FRONT OF VEHICLE, THE REAR A/C WORKS
GOOD. THE PRESSURES ON THIS VEHICLE READ OK, WITH AN
OCCASIONAL SURGE IN HIGH PRESSURE. THE VEHICLE HAS JUST HAD
A NEW ACCUMULATOR AND THE BLEND... |
View |
|
2001 Chevrolet Suburban 5.3L intrument cluster this truck came in customer states instrument panel lights
dont work but sometimes she hits a bump and they flash on .
Of course i thought short then i determined it was the gray
wire into the ip cluster that has no power but the only
info i have on this wire ... |
View |
|
2005 Chevrolet Tahoe 5.3L abs good afternoon
i have a 2005 tahoe 4wd here, the complaint is when you
take off from a stop the traction light comes on and the
truck will not accelerate for about 3 seconds. i checked
for codes and there is none, hooked tech2 up to watch data
and there is no... |
View |
|
2006 Chevrolet HHR 2.4L MIL Lamp on I have this 2006 HHR here that is being a nightmare! It
came in with codes P0121, P2176, P2135, and P2119. All for
the two TP Sensors after testing the ckts and driving the
vehicle trying to get it to act up we finaly replaced the
throttle body with both the T... Trouble codes: P2135 (TP Sensor 1-2 Correlation). |
View |
|
2007 Chevrolet Tahoe 5.3L rear glass please help. problem is the the rear glass on the lift gate
opens by its self when you operate the power lift gate open
and close. it will mainly pop open when its closing. one
time it popped open with just closing the driver door and
once with inserting the k... |
View |
|
2002 Chrysler PT Cruiser 2.4L Inaccurate This PT Crusier was just purchased off a used car lot. The
customer came in complaining it "uses too much gas".
I know I get this every time gasoline prices rise, so I
asked if he tracked his gas mileage. The customer says, "I
don't have to... All you have t... |
View |
|
1997 Dodge Pickup 5.2L rear anti lock the abs light is on intermittently. scan tool will not read
this system. mitchell, alldata & identifix instructions say
to ground pin 13 of the underdash connector to start the
light flashing codes. pin 12 & 13 are blank on this
connector. any ideas ? |
View |
|
2001 Dodge Pickup 5.9L front pads All brake functional tests appear normal as to apply and
release operation with veicle on lift. No delayed apply or
delayed release observed. Road test after installation of
severe duty (aftermarket) pads and new rotors reveals
normal pedal feel and function. ... |
View |
|
2003 Dodge Neon 2.0L engine Hello all, hope you can help us out with this problem neon.
We had this car come into the shop with a complaint of
engine noise, we isolated the noise down to the water pump
so we replaced the timing belt, water pump, and timing belt
tensioner. (dealer parts) ... |
View |
|
2003 Dodge Pickup 5.9L Cuts out P0341 cam sensor code Trouble codes: p0341 (cam sensor). |
View |
|
2004 Dodge Durango 4.7L all I test drove it to confirm the running hot, trans shifted
fine, pulled it up to the bay, the tech does the water
pump, (plastic impeller breaks and don't pump efficiently)
and was going to test drive it and the trans will do
absolutely nothing no matter what g... |
View |
|
1998 Ford Pickup 4.6L Rear Brake Lock up Rear Right Brake Lock-Up coming to a stop 10 mph or less.
Linings are Great. Clean & Dry. Replaced Shoes, hardware &
adjusters at last brake job. Machined Drums with a smooth
finish. Replaced shoes again with thermo-quiet shoes. Seems
to be good for a whyle, t... |
View |
|
2003 Ford Econoline 6.8L Electronic Hi. Techs. I need help. This van with 4R100 transmission
has very rough shifting from 1st to 2nd gear, sometimes at
40mph. There is a DTC P782 '2-3 shift error' code. The a/t
fluid is not burnt. No abnormal data readings I can see. I
am suspecting shift soleno... |
View |
|
2002 GMC Yukon 6.0L secutity i know passlock problems are a crap shoot but i got extra
info with this one. the MIL doesn't come on with the
ignition. the complaint is the security kicks in
occasionally leaving her stranded in 10 min intervals. BCM
kicks a B2960 sig incorrect but valid, no... |
View |
|
1996 Honda Accord 2.7L Unknown This 96 accord came in with a complaint of a brake pedal
issue? First road test all that was felt was a pulsation.
Inspected and mechanicals look ok. Found in shop with
vehicle running the pedal will fade/drop some with light
pumping of the pedal.(like bad mas... |
View |
|
2004 Hyundai Santa Fe 3.5L cylinder head dropped a washer into engine while changing spark plugs now
embedded in cyl head service info recommends to remove
engine to remove cylinder head is this the best way to
approach this repair any advice would be gratefully
received |
View |
|
2000 Infiniti I30 3.0L MIL Lamp on Open to any and all ideas. Direct question concerning the
knock sensor - will the ECM create a problem in the absence
of the knock sensor input? (According to Alldata the knock
sensor DTC will not illuminate the MIL).
Car otherwise starts and runs fine. Trouble codes: P0430 (Cat efficiency low bank 2), P0325 (Knock sensor failure). |
View |
|
1998 Jeep Grand Cherokee 4.0L guages,windows,locks I have a problem for the Chrysler guys. Customer came in
stating that he went to unlock the car with the key fob and
the drivers door didn't unlock. However all the other doors
did. Upon entering the vehicle he noted that the D/S door
lock switch only locked/u... |
View |
|
2005 Kia Optima 2.4L vibration thanks for you're replies ahead of time!
Let's get started shall we? 05 Optima, 2.4 4 cyl, comes in
for timing belt job/water pump, no biggie. This car also
has a alance shaft belt, seperate from the timing belt. On
removal, i brought everything up to TDC, c... |
View |
|
2003 Land Rover Range Rover 4.4L air bag light hi guys we scanned this truck for codes with launch we got
codes 62 and 74 but no definition what i need is the
deffinitions for these 2 codes we used the launch and this
is all i could get out of it all help is needed thanks |
View |
|
1996 Lexus LS 400 4.0L CD player Good Evening
When the customer puts a CD into the CD player(player is in
back of console), "ERROR 21" is displayed on the dash unit
audio system. What is ERROR 21? Thanks for any info you can
give us on this.
glen |
View |
|
1998 Lexus ES 300 3.0L abs module Hey Guys,
We recently serviced this vehicle for rear suspension strut
replacement due to a soft suspension complaint. All went
well with no complications but when the vehicle was picked
up after sitting dormant for a week or so the "abs" and
"trac" warning la... |
View |
|
1996 Lincoln Town Car 4.6L Digital speed Car came in,states speedo reads 120mph at idle, when moving
reads from 75-95mph (While cruising 5MPH), replace VSS &
speedo head, still the same,one thing I discover that if
you move sensoraway from transmission while still idling in
Park, speedo shows Omph, i... |
View |
|
2000 Lincoln Navigator 5.4L air conditioning Air conditioning blower changes at random from vents to
defrost and remains on defrost unless vent button is pushed
changes over but when ac max is pushed again stays on vents
for a short period of time then changes to defrost again.
Checked for a vacumn leak ... |
View |
|
1993 Mazda MX-3 1.8L Stall Hi All mazda tech's
just a quick question I have a 93 mx3 (mine) I think I have
a bad iac motor. reason being. either driving or at a stop,
Idle speed hangs at 1500 rpm for aprox 45 seconds then
drops to 1,00 rpm for a few seconds then drops to dead it
drops ... |
View |
|
1994 Mazda 626 2.5L shifting After the tranny was installed they could not make the car
run.
I found the ECM toasted. Replaced with a reman unit. Found
codes for the coolent temp sensor, the EGR and the right O2
sensor. Test drove when the tranny shifts out of first it
freewheel. I have... |
View |
|
1987 Mercedes-Benz 190E 2.3L Poor Idle Quality, Misfire This 190E was running great until 4 days ago. It just
started up cold and ran rough for the customer. At idle is
the worst. Off idle is ok and it seems good under load.
Feels like a vacuum leak or a restricted injector. I
checked the compression, good at about... |
View |
|
1988 Mercedes-Benz 300SE 3.0L Poor Idle Quality, Hesitation, Surge, Stall, Misfire Hello People,
I have one thats got me stumped.
After original repair, the vehicle (putting it mildly)
"runs like shit"
This situation all started after replacing the A/C
compressor clutch.
Brief description of original diag. and repair
DRIVER COMPLAINT= A... |
View |
|
1988 Mercedes-Benz 560SL 5.6L compressor comp clutch draws 2.5 amps and engages when manually
activated. |
View |
|
1995 Mercedes-Benz S320 3.2L Reverse and low TRANS IS 722.371
Vehicle came into shop for a complaint of slipping in
reverse gear, once vehicle had been driven for 20-30
minutes.
We removed the transmission and torque converter and had
both rebuilt.
Upon dissasembly we found the B3 frictions to have wo... |
View |
|
1997 Mercedes-Benz E320 3.2L Sun roof motor Sunroof had broken lifting mechanism and kinked sunroof
cables. All replaced. Roof operates perfectly - EXCEPT - in
"pop-up" motor does not stop. Runs until cables hit limit
and make snap noise. Tried motor from wrecking yard? Cannot
see anything wrong with ei... |
View |
|
1998 Mercury Sable 3.0L Excessive Emissions Hello to all again, need some help on this emission failure
at 25 mph. The emission readings that are given were the
test results from the I/M inspection(idle specs are the 15
mph results and cruise specs are the 25 mph results). After
running the numbers on t... |
View |
|
2002 Mitsubishi Lancer 2.0L door locks/interior light The power door locks will not work except with the key on,
all doors lock and unlock fine as long as key is on, but
when key is off they won't lock or unlock from any door
switches or the key switch in the lock cylinder. This
supposedly happened after stereo i... |
View |
|
1996 Nissan Maxima 3.0L Excessive Emissions, No Start, Poor Idle Quality, Misfire PLEASE HELP, I am stuck in the worst way. dont usually ask
for help but i dont know whare else to go with this one.
This nissan maxima came in about 2 weeks ago with an
extended start. it would crank crank hold the gas to the
floor & it would start. As if it w... |
View |
|
2005 Nissan Maxima 3.5L No Start, Poor Idle Quality, Misfire PLEASE HELP, I am stuck in the worst way. dont usually ask
for help but i dont know whare else to go with this one.
This nissan maxima came in about 2 weeks ago with an
extended start. it would crank crank hold the gas to the
floor & it would start. As if it w... |
View |
|
2001 Oldsmobile Aurora 3.5L Misfire, MIL Lamp on So this is the worst kind of problem you can have...one on
your own car... I'm in the process of buying this Aurora
from my mother in law, after telling my wife for the last
year that we didn't want to touch it cause these things are
problem pits! It set the m... Trouble codes: PO131 (O2 - 1 low), PO137 (O2 - 2 low), PO300 (Randommultiple misfire). |
View |
|
1998 Plymouth Grand Voyager 3.3L gauge gas guage works intermittent,driving along goes to empty
and low gas light comes on.then goes back to correct
reading at various times.fuel meter has been replaced and
ground checked |
View |
|
2000 Saab 9-5 2.3L locks, antitheft Hello SAAB guys, got this 2000 9-5 that came in for a bad
oil leak, found oil pressure switch separated and leaking
badly. Ordered switch from dealer and in the meanwhile,
waiting for the next day delivery, disconnected battery
negative terminal, removed start... |
View |
|
2002 Subaru Impreza 2.0L icing on low side line and evap We replaced the expansion valve due to having vacuum on the
low side. After repair the low side line from compressor to
the evap is icing up, as well as the core itself. Pressures
after repair are 25 and 135 high side. Compressor runs for
a bit then stops |
View |
|
1999 Toyota Avalon 3.0L srs Toyota Techs... This car keeps coming back with an airbag
code (44) (pass side open squib). A freind of mine at the
local toy dealer says its usally a bad connection under the
passenger seat. I have cleaned, checked, tighened, bent
contacts etc..., & every two... |
View |
|
1999 Toyota Sienna 3.0L Door Lock LH front door electric door lock actuator will not
function, lock or unlock. From master switch all other door
locks function correctly. Key from out side will unlock all
doors when you turn the key the second time within 3 sec.
and lock them also. When you ha... |
View |
|
1999 Toyota Avalon 3.0L MIL Lamp on i have a code 171 both af sensors.stay at .630 when i
disconnect both sensors voltage wiii not change .with
sensors connected & running still no change.i have 12v at
blue wire.on both sensors also ground at both.with sensors
disconnect should should i still se... Trouble codes: 171 (lean exh. bank 1). |
View |
|
2000 Toyota 4Runner 2.7L Misfire, MIL Lamp on Car came to me with the check engine light and it had a
misfire in cyl # 3. Found #3 injector was not firing. I
replace the injector but now the engine runs rough at idle
and at times the miss comes back. The code also returns.
Hc, co, and o2 are neer zero at ... Trouble codes: P0300 (random misfire), P0303 (cyl. 3 misfire). |
View |
|
2001 Toyota Sienna 3.0L Poor Idle Quality, Cuts out, Stall This is the second time we have seen this problem on this
vehicle. Six months ago it came in for stalling unless you
kept your foot on the gas. When it is running under load,
there does not seem to be any misfires. There were no codes
in the computer and prope... |
View |
|
2002 Toyota Highlander 3.0L VSC Light Help Toyota Techs, we put a timing belt on a 2002
highlander. Now the VSC light illuminates as soon as you
move. It also has a code C1336 zero point calibration of
deceleration sensor undone. I would greatly appreciate some
feedback. |
View |
|
1994 Volkswagen CAMPER VAN 2466CC Aux. Battery I am having trouble finding the auxillary Battery. The
information says under the drivers seat, but it definately
isn't there and we have looked through most of the van. Any
one have any suggestions. Thanks |
View |
|
1995 Volkswagen Cabrio 2.0L engine Odd thing is, tach starts to fluxuate a little, then stalls
for 30 to 45 seconds. Pull any plug wire off and starts up
on 3 cylinders, replace and stalls immediately. Pre obdII,
and no check engine light at all. Super low miles! Any
ideas? Next trick was to go... |
View |
|
1999 Volkswagen Passat 1.8L MIL Lamp on This one is driving me crazy. came in with these two codes
i have tested the cam and crank sensor with vantage scoped
both. I have removed ecu and ohm cheaked wires form the
sensors to the ecu all have no resistance. I have cheaked
the basics/ timing the timin... Trouble codes: p1337 (bank 1 cam position sensor short to ground), p0322 (crank sensor no signal). |
View |
|
2002 Volkswagen Jetta 1.8L seals i have replaced cam and crank seals and timing belt, twice
and valve cover gasket set. it keeps leaking oil out of the
front? i cannot see exactly the spot, but the leak got
worse when i changed seals. also i tried a different brand
of seals the second time. t... |
View |