|
|
1981 Ford Pickup 6.6L shaft lock pin
Good day!
I have a 1981 F250 4X4 here with a Dana 60 semi floating
rear axle, and I need to replace the rear wheel bearing and
seal. It is a semi floating axle with "C" locks on the side
gears. The pinion shaft appears to be held in with a roll
pin from what ... |
View |
|
1993 Ford Mustang 5.0L Poor Idle Quality, Poor Fuel Economy
This vehicle is actually a 1986 Volvo 240 Wagon with a 1993
Mustang 5.0 engine, drivetrain, and computer control system
implanted. This Volstang is here for several things, but
the customer's main complaint is that he's getting poor
fuel mileage and a rough id... Trouble codes: 95 (Secondary Fuel Pump Circuit Failure). |
View |
|
1998 Ford Econoline 5.4L Alarm or PCM?
Vehicle was operating fine when parked for 2 weeks. When
attempting to start, starter runs but engine doesn't start.
Then noticed that when key is turned on,PCM & fuel pump
relays cycle open & closed like a flasher - also service
engine light blinks on & off w... |
View |
|
1998 Ford Escort 2.0L clutch
we have this escort zx2 with a/c clutch inop.first ck'd a/c
pressures which were ok.then fuses and wiring
connections-ok.checked power through a/c low press.
switch-ok.voltage travels from a/c switch to low side
sw.tees to pcm then to contact side of ccrm rela... |
View |
|
2005 Ford Explorer 4.6L MIL Lamp on
At first I had a code on this explorer for excessive egr
flow, voltage was high, changed egr valve and sensor assy.
Its all in one on this vehicle. Now its reading a lower
voltage, but still must be too high, because it sets the
same code. also codes eventuall... Trouble codes: po402 (excessive egr flow), po193 (fuel pressure high input), po453 (evap control high input). |
View |
|
1976 Ford F600 390CID Pedal height
Thank You for all the replies! I bleed front to back,back to front, open bleeder pedal down, pump pedal apply and open bleeder, powerbleed/pressure bleed, vaccuum bleed, checked bleeder positions for proper location, pinched off hoses, adjusted brakes. But bef... |
20 |
|
1989 Ford Ranger 2.3L Poor Idle Quality, Stall, Misfire
im still driving the truck with no spark advance. i haven't found a salvage yard with the correct module yet. Trouble codes: 14 (Ignition pickup PIP was erratic), 18 (Loss Of Ignition Diagnostic Module Input), 28 (Loss Of Ignition Diagnostic Module RH Side), 48 (Loss Of Ignition Diagnostic Monitor LH Side), 88 (Loss Of Dual Plug Input Control). |
5 |
|
1994 Ford Pickup 5.0L MIL Lamp on
problem was ecm after checking all grounds ecm was removed and found to have water in it thanks to all who responded |
9 |
|
1996 Ford Windstar 3.8L Poor Idle Quality, Hesitation, Surge, Cuts out, Stall, Misfire, Poor Fuel Economy, MIL Lamp on
Well so far so good. As I said I cleaned the maf and throttle body. I cleaned the iac and carbon cleaned the intake. this seems to have solved the problem. I drove the car for a few days and the problem didn't reoccur at all. the customer is gonna let us know ... Trouble codes: P0171 (bank 1 lean), P0174 (bank 2 lean). |
25 |
|
1999 Ford F550 Super Duty 7.3L Excessive Emissions, Surge, Cuts out, Stall, Misfire
thanks to all for all of your great ideas, we were running the vehicle on the dyno while testing and decided to install a pressure guage in front oil reservoir,when the vehicle would act up the dash oil guage would read high normal,however the mechanical guage... |
9 |
|
1999 Ford Pickup 7.3L Poor Idle Quality
after replacing 3 injectors ...cylinder 8 and 7 are fixed.. cylinder 5 compression went down just pulled the head off today cylinder wall has a grove on it waiting to see what the boss wants to do ... thanks to all that ofered help . Trouble codes: P0275 (cylinder 5 contributionbalance fault), P0281 (cylinder 7 contributionbalance fault), P0284 (clyinder 8 contributionbalance fault). |
16 |
|
2000 Ford Pickup 7.3L No Start
thank you all for the help. I took both plugs out and filled the hpop res up and cranked for about 30 secs and it finally took. |
8 |
|
2002 Ford Pickup 7.3L Misfire, MIL Lamp on
Dear techs in IATN land. Sorry I've been so long closing this post. We have had quite a round with this truck. I have the truck running much better, but still have some problems yet. 2 of the replys said my problem is the rebuilt injectors and one thought it w... Trouble codes: P0773 (gear ratio 3 incorrect), P1670 (EF feedback not detected), P1247 (turbo boost pressure low), P0476 (exhaust backpressure sensor voltage), P0284 (cylinder 8 balance), P0269 (cyl 3 balance). |
3 |
|
2003 Ford Crown Victoria 4.6L wipers
new wiper motor and connecter installed today and its back to normal. thanks for the help. |
7 |
|
2005 Ford Pickup 6.0L No Start
Cam positions sensor replaced. That fixed it.
Thanks. Trouble codes: 2291 (Injector pulse too low), 2614 (Camshaft position circuit open), 2617 (same). |
6 |
|
Prev
