|
1996 Ford Probe 2.5L Hesitation, Cuts out
Hello fellow techs,this FORD PROBE was towed to our
shop,cranking and no start,fuel pressure was ok,cranking
vacuum was also good,but the spark plug wired were in bad
shape,i was getting good spark out of dist cap, so got a
new motor craft plugs and wires,also... |
View |
|
1997 Ford Explorer 4.0L No Start
customer had misfire code 3 and 6 replaced coil wires and
plugs themselves. now car for last two days took 15 mins of
key cycling to start. off to start. car cranks the whole
time but no start. as of now can not duplicate problem.
everything else checks out Trouble codes: b1352 (ignition switch malf). |
View |
|
1999 Ford Ranger 4.0L steering wheel
customer is complaining of a poping noise over small bump
(parking lot) and @ low speed (15 ta 25 mph) i can get it
too make the noise @ same lot & cant hear it @ highway
speeds the noise sounds like the gm itermediate shaft no
grease cond. |
View |
|
1999 Ford Pickup 5.4L 4x4 shift motor
Hello all, This F150 is giving me fits;got a code p1815
(tran 4wd mode select sht gnd) as an ondemand code from the
gem module but MOD seems to have let me down here,no
info.that I can find.
Also there are GEM codes in memory P1832 ( see service
manual) and p... |
View |
|
2002 Ford Pickup 7.3L No Start, MIL Lamp on
OK, here's one that's givingme a headache. Truck was towed
in for a no start, checked fuel pressure- 60 PSI. Hooked up
scanner- VPWR-11.6 volts, RPM 180, ICP 262. Fuel PW 5.034,
Vref-4.99. I saw the low ICP readings and took a gamble and
put an IPR on it. No c... Trouble codes: 1211 (Low ICP). |
View |
|
2002 Ford Explorer 4.6L Stall, Misfire
Hope you Ford guys can shed some light on this one. It
missfires under load on highway but shows no missfire
counts or codes. It will also stall at idle after warm. It
idles fine and then just shuts off. Starts right up and may
not do it again for several minu... Trouble codes: 1336 (crank sensor circuit). |
View |
|
2002 Ford Ranger 4.0L Battery
Hello Ford Techs. I have an electrical short in this truck
that kills the battery in 4 hrs flat. I have disconnected
everything I think would affect this problem. I've
connected my labscope in series on the negative side on the
battery post and battery cable. ... |
View |
|
2003 Ford Pickup 4.6L vibration
Hi all need help on this one. This truck came to us with
the trans cooked and almost locked up. We replaced the
trans with a rebuilt unit complete with torque convertor.
Since replacement the truck has a vibration that can be
felt throughout the truck. The vib... |
View |
|
2003 Ford Windstar 3.8L dome light
Hi Ford guys,
This one has me puzzled. The light on the dash lights up as
if a door was open, however, the dome and the cargo lights
do not come on. They will turn on manually at the light
switches and the dimmer switch. There is 12 volts at both
pins 2 and 3... |
View |
|
1993 Lincoln Mark VIII 4.6L Cruise Control
Hello all, and thanks for your help in advance.
This vehicle has an inoperative cruise control. I checked
the fuses (Of course they were good) I then took the air
bag off and checked the switches on the wheel with an ohm
meter to make sure they would turn on ... |
View |
|
2000 Lincoln Continental 4.6L steering gear, lines,pump.
this car came in for a rattle noise when ever there is a
load on the power steering. eg. idling in the shop with
wheels on the ground, turning slightly to load pump. there
is a rattle and a pulsation you can feel in the pump and
the high pressure line. it can ... |
View |
|
2003 Lincoln Town Car 4.6L Compressor
Hello all,
We have several of these vehicles in our fleet. This one
came in with a/c inop. Of course the first thing I do is to
hook up the a/c machine to see if the system has freon.
Which in this case, it does. Removed the clutch relay and
jumped the connec... |
View |
|
1999 Mercury Grand Marquis 4.6L MIL Lamp on
customer called in for no start problem.went to customers
house and replaced #12 maxi-fuse.drove car to shop.started
checking over,found fuse would blow when ign. was in
run,not start.pulled wiring diagram,started checking
resistances on circuit no problems fo... Trouble codes: P1451 (evap system vent control valve fault). |
View |
Prev
