Prev iATN Members TechHelp for July 24, 2008
Automotive Technical Exchange for the Automotive Repair Professional		 Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for Chrysler
Help Request Answers
1995 Chrysler Cirrus 2.5L Anti Theft
So this vehicle came into our shop with a no start condition. We narrowed down the possibilities to a faulty distributor. About 1 week later it came back again with a no start condition. We found the crank sensor to be out of spec as it had coded up. We change...		 View
2005 Chrysler Town & Country 3.3L abs system
good morning guys and gals, the vehicle came in for abs light on, found two codes for rr speed sensor. tested sensor found resistance to be open and not reading mph signal thru scanner.replace sensor now i have a signal reading but will spike high 90 percent o...		 View
2002 Dodge Caravan 3.3L Hesitation, Surge, Misfire, MIL Lamp on
I have spent a lot of time checking MAP sensor voltages and road testing.The van jerks and surges and seems to be miss firing, however I do not get any miss fire information.MAP voltage has been OK ,I also ran a new ground wire from the MAP sensor to the PCM.I... Trouble codes: P0107 (map voltage low).		 View
2003 Dodge Pickup 5.9L transmission
please help I've got this dodge truck here that is in limp home mode 2nd gear, pcm is not grounding transmission relay,relay has constant & ign voltage 12.5 volts to it traced back trans relay control circut back to pcm .7 ohms on control wire. I also noticed ...		 View
2005 Dodge Durango 4.7L front control module
OK , we had a 05 dodge durango brought to us from a local car lot. The previous shop had removed some modules off this vehicle to try to repair another 05 Durango. They did repair the other vehicle but at the expense of this one. supposedly! The other vehicle ...		 View
2001 Jeep Grand Cherokee 4.7L MIL Lamp on
The check engine lamp comes on and the fault code p0118 comes up. I cleared the fault and it was back the next day. I then checked th plug connection to the temp sensor and it appeared ok. I then replaced the coolant temp sensor at the frt of the cyl head area... Trouble codes: p0118 (engine coolant temp sensor above maximum voltage).		 View

Fixes & Summaries for Chrysler
Fix/Summary Answers
2001 Chrysler Town & Country 3.8L compressor
Thanks to all that replied. We found that the ambient air temperature sensor was completely unplugged. After looking closely at the front of the vehicle, we noticed that it had some fresh paint work on it, and apparently the sensor hadn't been plugged in ...		 9
1998 Jeep Wrangler 4.0L MIL Lamp on
Thanks guys!!! Now I don't feel stupid, who'd of thunk it? Like you all said clock spring was the problem.I thought V.W. had the record for stupid shit, but I'd of never have figured clock spring. Never would of fixed this one without your help!Thanks to all!!... Trouble codes: P0123 (TPS voltage High).		 8
1998 Jeep Grand Cherokee 4.0L No Start
Mike, Dave, and Rick all pointed towards the CKP being shorted but as I said in my original post the sigals all looked good. I had already checked them with a scope(my fave tool). I replaced the Rear O2 that had the wires pulled out of it and the PCM and it ...		 4
1999 Jeep Cherokee 4.0L front end
Thanks for all of the helpful input.After replacing upper and lower control arms,upper and lower ball joints,steering gear,shocks,hub assemblies,rotors,track bar,sway bar bushings,links,tie rod ends,and pittman arm ,we were no closer to fixing the noise than w...		 6
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next